MP360 4-Sided Planer / Moulder

$16,995 

High-production, large capacity four-sided planer/moulder with 4 cutting heads, 5 individual motors, 13 3/4” wide x 6” high four-sided planing / moulding capacity, 12 – 60 fpm variable power feed, and 7,200 rpm spindle speed.

Share This Page:

MP360 Planer/Moulder Overview

The MP360 four-sided planer/moulder is a high-production, large capacity machine engineered for professional workshops. With a larger capacity and higher hourly production levels than the popular Wood-Mizer MP260 planer/moulder, the MP360 planes and moulds boards on all four sides in a single pass into a variety of professionally finished products.

The MP360 planer/moulder has four cutting heads with the ability to produce single, two, three, and four-sided final products in various profiles. The MP360 has user-friendly measurement scales with a large 13 3/4” (350mm) wide x 6” (150 mm) high capacity for four-sided planing/moulding. The capacity for one-sided planing  is 20” (510mm) x 9” (230 mm) and two-sided planing/moulding is 16 1/8” (410 mm) x 9” (230 mm). For two-sided planing/moulding, the table and machine height are adjusted together from 3/8”- 9” (10 – 230mm) to precisely align and optimize material entering the machine.

A centralized control panel allows the operator to start and stop the chip extraction system, four cutter motors, and power feed motor separately. With the same 4HP (3kW) vertical cutter motors as the MP260, the MP360 features more powerful 7.5HP (5.5kW) top and bottom horizontal cutter motors for increased production. Four steel and one polyurethane power roller steadily move the board through the machine to ensure a consistent profile from end to end even with uneven boards. The feed rate is faster than the MP260 and adjustable from 10 – 49 ft/minute (3-15 m/minute) to efficiently process both softwood and hardwood material.

Inside the machine, the large top and bottom horizontal cutters and tall two vertical spindles on the right and left of the machine plane or mould the board at 6,000 rpm to ensure a smooth and consistent finish on one, two, three, or all four sides depending on which cutters are activated. A large viewing window allows the operator to supervise the entire cutting process from rough sawn boards to final products. Various extraction points are located near the cutters to keep chips from building up in the machine. Wood-Mizer provides multiple chip extraction systems depending on your operation needs.

The high-production MP360 planer/moulder is built to last with a heavy-duty cast-iron table, durable sheet steel chassis, and premium components. By combining multiple planing and moulding knives, the extremely versatile MP360 can produce everything you need from baseboards and flooring to wall paneling and crown moulding.

In addition to the four standard planing knives provided with the machine, Wood-Mizer offers a range of moulding knives to produce the exact product you need for your project or client. Changing knives is simple and takes approximately 10 to 20 minutes which makes the production of small quantities of custom material more efficient and profitable. Operators occasionally stock extra cutters with common knife profiles installed to save time when needing a new profile.

The MP360 four-sided planer/moulder ships on a single pallet, comes with a complete set of four planing knives, and requires minimal assembly time so you can start producing professionally finished planed and moulded products within a few hours of receiving your machine. With a 30-day money back guarantee and 2-year warranty, the MP360 is backed by the same legendary service, quality and safety features shared by the entire family of Wood-Mizer wood processing equipment.

MP360 Planer/Moulder Standard Features

Centralized Control Panel

Allows the operator to start and stop all four cutter and power feed motors separately.

LT15 Head Up/Down

Easy-to-change Knife Profiles

Changing knives is simple and takes approximately 10 to 20 minutes which makes the production of small quantities of custom material more efficient and profitable.


Five Feed Rollers

Four steel and one polyurethane power roller steadily move the board through the machine to ensure a consistent profile from end to end even with uneven boards.

Log Clamps

Variable Feed Rate

Is adjustable from 12 – 60 ft/minute (3.6 - 18 m/minute) for 60 Hz to efficiently process both softwood and hardwood material.

Adjustable Height

The table and machine height are adjusted together from 3/8" - 9" to precisely align the material entering the machine.

Easy Shipping and Assembly

Heavy-duty Construction

Built to last with a heavy-duty cast-iron table, durable sheet steel chassis, and premium components. 

4 Cutting Heads

Plane and mould boards on all four sides in a single pass into a variety of finished products.

LT15 Head Up/Down

Multiple Extraction Points

Located near the cutters connect with your chip extraction system to keep chips from building up in the machine.


Large Viewing Window

Allows the operator to supervise the entire cutting process from rough sawn boards to final products.

Options

Planing and moulding knives
Chip extractor system
Table extensions
Rubber feet rollers 
Power feed 13’ - 78’ 8” ft/min (4 - 24 m/min)

Machine Dimensions

Length & Width
9’ 9” x 3’ 8” (2,970 mm x 1,125mm)
Height
56” (1,430 mm)
Weight
1,488lbs (675 kg)

Specifications

Capacity
4 Sided Planing/Moulding Max. Width - 13 3/4" (350mm)
Height - 3/8" - 6" (10-150mm)
2 Sided Planing/Moulding  Max. Width - 16 1/8" (410mm)
Height - 7/16" - 9" (10-230mm) 
1 Sided Planing/Moulding Max. Width - 20" (510mm)
Height - 9" (230mm)
Upper Horizontal Cutter
Diameter 3 7/16" (88mm) 
Width 20" (510mm)
Power 7.5 HP (5.5kW) 
Speed 6000 rpm (50 Hz and 60 Hz)
Max Cutting Depth 5/16" (8mm)
Max Profile Depth 3/4" (20mm) 
Lower Horizontal Cutter
Diameter 2 13/16" (72mm) 
Width 16 1/8" (410mm)
Power 5.5 HP (4kW) 
Speed 7200 rpm 60 Hz / 6000 rpm 50 Hz
Cutting Depth 0 - 5/16" (0 - 8mm)
Profile Depth max 3/8" (10mm)
slot drill 1/2" (15mm) 

Vertical Cutters
Spindle Diameter 1 3/16" (30mm) 
Max Cutter Height 5" (130mm)
Max Diameter 5 1/2" (140mm) 
Power 4 HP (3 kW)
Rotation Speed 7200 rpm 60 Hz/ 6000 rpm 50 Hz
Max Cutting Depth 1 3/16" (30mm) 
Standard Planing Knives Included
Type TB90 steel
Diameter Head 3 9/16" (90 mm)
Height Head 1 9/16" (40 mm) 
Knife Type HSS
Knife Width 2" (50 mm) 
Power Feed
Power 1 HP (0.75 kW)
Feed Speed 12-60 ft/min (3.6 - 18 m/min) 60 Hz
10-49 ft/min (3-15 m/min) 50 Hz
Electrical
Total Power 22 HP (16.25 kW)
Connection 3Ph 230V, 50-60Hz, 32-50A